Programming the mePed

Discuss and share software for making your mePed navigate and move about in the real world
mikegre
Posts: 1
Joined: Sat Oct 14, 2017 10:35 pm

Programming the mePed

Postby mikegre » Sat Oct 14, 2017 10:39 pm

I have connected the mePed up to my computer where I am running the Arduino web IDE. When I attempt to upload a new sketch I'm getting the following error:

Code: Select all

Flashing with command:/Users/michael/.arduino-create/arduino/avrdude/6.3.0-arduino9/bin/avrdude -C/Users/michael/.arduino-create/arduino/avrdude/6.3.0-arduino9/etc/avrdude.conf -patmega32u4 -cavr109 -P/dev/cu.wchusbserial14420 -b57600 -D -Uflash:w:/var/folders/p0/5t1z69ln2g18m1zchmpsfsym0000gn/T/arduino-create-agent073869932/sketch_oct14a.hex:i

Connecting to programmer: .avrdude: butterfly_recv(): programmer is not responding

avrdude: butterfly_recv(): programmer is not responding

avrdude: butterfly_recv(): programmer is not responding

avrdude: butterfly_recv(): programmer is not responding

avrdude: butterfly_recv(): programmer is not responding

avrdude: butterfly_recv(): programmer is not responding

Found programmer: Id = ""; type = 

Software Version = .�; Hardware Version = .

avrdude: butterfly_recv(): programmer is not responding

avrdude: butterfly_recv(): programmer is not responding

avrdude: error: buffered memory access not supported. Maybe it isn't

a butterfly/AVR109 but a AVR910 device?

avrdude: initialization failed, rc=-1

Double check connections and try again, or use -F to override

this check.

avrdude: butterfly_recv(): programmer is not responding

avrdude: error: programmer did not respond to command: leave prog mode

avrdude: butterfly_recv(): programmer is not responding

avrdude: error: programmer did not respond to command: exit bootloader

avrdude done. Thank you.
What do I need to do to get this to work?

Thanks,

Mike

spierce
Site Admin
Posts: 37
Joined: Thu Sep 29, 2016 6:43 pm

Re: Programming the mePed

Postby spierce » Tue Oct 17, 2017 7:57 pm

Hi Mike,

I'm sorry for your troubles! To be honest, I haven't tried out the web interface. Would you mind downloading the full IDE onto your computer and try programming the Arduino on the mePed that way? Please also be sure to select the Arduino Nano controller, select the correct COM Port, as well as have the correct CH340 Serial Drivers installed for your computer. These can be found on www.mePed.io.

Please let us know if you need further assistance.

Thanks,
Scott Pierce

gjwheat10
Posts: 1
Joined: Sat May 26, 2018 11:02 am

Re: Programming the mePed

Postby gjwheat10 » Sat Jun 02, 2018 7:54 am

I bought a kit at the Make Faire. After some confusion I finished the model. It has never worked. It only hums and twitches on startup. I tried to upload the program on the Nano but I get error messages. Is there a different place to get the files. Both the sketch on the forum and the one on the website do not work for me. I have copied them into the IDE and tried to upload them. Am very frustrated.

cTurtle98
Posts: 2
Joined: Sun Jun 03, 2018 1:11 pm

Re: Programming the mePed

Postby cTurtle98 » Sun Jun 03, 2018 1:14 pm

I found this
https://github.com/ptbw/MePed
it might be useful


Who is online

Users browsing this forum: No registered users and 3 guests